The City of Seguin is soliciting bids for a vendor to provide for the purchase of AVT EZ insertion valve product kits. The intent of these specifications is to describe the minimum requirements for the purchase of these products.
4" - 8" EZ Valve Equipment Packing List
EZM1H/E/P Complete Service Kit for 4"-8" EM Machine – 1
Pressure Tested
Machine Spins in correct direction 45mm Cutter Fits
60mm Cutter Fits
Back-out Prevention Washer – 1 Fits on Shaft
Hand Wheel for Drilling – 1 Fits on Feedscrew
EM Mounting Ring – 1
Is attached to Machine Has Blow-off
Has O-ring Transition Ring – 1
Has 2 O-rings Fits in 4" Plate
Fits in 6" Plate Fits in 8" Plate
EM 45mm Cutter – 1
Has Pilot
Has Pilot Screw Has 2 Right Teeth Has 4 Left Teeth
Has 45mm Torx Screwdriver EM 45mm Teeth – 1
Has 2 Right Teeth Has 4 Left Teeth
4" Mounting Plate – 1
4 Holes Tapped
6" Mounting Plate – 1
4 Holes Tapped
8" Mounting Plate – 1
4 Holes Tapped EM Mounting Bolts – 4
Turned Down 4" End Ring Set – 1
Hardware in Tapped Holes 6" End Ring Set – 1
Hardware in Tapped Holes
8" End Ring Set – 1
Hardware in Tapped Holes Gear Box – 1
Sprocket Set Correctly Handle Attached
Fits on 4" Ring Fits on 6" Ring Fits on 8" Ring
Drive Unit Bolts – 2
Fit Easily into Rings Chain – 1
Thread is Tapped Correctly Hinge Moves Easily
Cam Faces Correct Way Stop-Pin – 1
2 Screws
U-Gauge Level Indicator – 1 Included
Chip Port Completion Machine – 1 Thread is Clear
Has Blow-off 45mm Chip Port Filling – 1
Thread is Clear
Has Plug Has O-ring Has Cap
Drain Hose – 1
Kink Free Clamps Attached
Secure Chip Collector Female Connector Secure Male Connector Secure
Debris Shavings Bag – 1 Tears Free
Included:
Crescent Wrench – 1
Flat Jaw Pipe Wrench – 1 Socket Ratchet Wrench – 1 15mm Combination Wrench – 1 17mm Combination Wrench – 1 24mm Combination Wrench – 1 30mm Combination Wrench – 1 Allen Wrench Set (metric) – 1 15mm Socket – 1
24mm Socket – 1 30mm Socket– 1 Paint Marker – 1
Level – 1
Tape Rule – 1
1" Ball Valve – 1 AVT FDA Tape – 2
AVT Grease (quarts) – 2 White Alcom Grease – 1 Black Molybdenum Grease – 1 PTFE Pipe Tape – 1
1-1/4" Wrench – 1
Reed Pressure Test Rig – 1
1" Female Cam Connector attached to hose with Teflon Attached male connection to top of unit with teflon
Equalization Jumper Hose – 1
1/4" Blow-off Facing Correct Direction 1" Female Cam Lock Connection
Training Manual – 1
MATERIAL SPECIFICATION NUMBER:
STOCK DESCRIPTION: Gasoline Powered Hydraulic Power Units
SPECIFICATIONS: High Performance Hydraulic Pump
Reservoir
Honda Gasoline Engine
Manifold Block
Relief Valve
Needle Valve
Return Filter
Pressure Gauge
Oil Level Dip Stick
These specifications cover a hydraulic system which employs enclosed fluid to transfer energy
from one source to another, and subsequently create rotary motion, linear motion, or force.
Hydraulic power units are self-contained systems that are generally built for the simple task of
converting mechanical energy into hydraulic energy. The gasoline powered hydraulic power
units covered by this specification shall consist of a high-performance hydraulic pump,
reservoir, Honda gasoline engine, manifold block, relief valve, needle valve, return filter,
pressure gauge and oil level dip stick. The power unit can be coupled via suitable hydraulic
lines to a wide range of operating mechanisms.
Statewide