A. Structural Firefighting Gloves 1. Construction: Total 3D construction, including thumb, for improved dexterity and comfort. 2. Palm: Digitized kangaroo leather for enhanced grip in wet or dry conditions. 3. Fingers: Split grain kangaroo leather 3D design to increase dexterity, flexibility, and durability. 4. Back of Hand: One-piece flat grain kangaroo leather to minimize seams and increase durability. 5. Knuckles: Ergonomic padding aligned with the natural curvature for protection and mobility. 6. Moisture Barrier: Porelle barrier for water resistance. 7. Thermal Liner: Kovenex liner for superior thermal protection. 8. Cuff: Exaggerated cuff design for rapid donning and improved wrist protection, integrating with turnout coats. Acceptance Criteria: Products delivered must match specifications, pass quality assurance testing, and meet agreed quantities and delivery timelines. B. Structural Firefighting Coat and Pant This specification defines the minimum requirements for structural firefighter personal protective equipment (PPE) providing limited protection as defined by NFPA 1971, Standard on Protective Ensemble for Structural Fire Fighting, Latest Edition. In the absence of comment on a particular point, industry standard practice shall be presumed to prevail. Every exception to specifications must be clearly spelled out at the time of bid. Coat 1. Outer Shell: 6.6 oz Agility with FREEFAS, Black Gold 2. Thermal Liner: 7.4 osy Glide Ice 2 Layer 3. Moisture Barrier: 5.5 osy Stedair 3000 4. Inspection Port Liner 5. Detachable Liner 6. SET Thermal Enhancement 7. Liner Label Pocket 8. Tail Drop – 5" 9. Positive Closure Articulating Rapid Rescue Strap 10. Trim: NFPA lime 2-tone Scotchlite (3"), Double-Stitched 11. Hem Patch with Velcro – Agility, Black Gold FREEFAS 12. Firefighter Last Name – average 7 letters, 2" letters if required 13. Lettering: “C.U.F.D.” – 4 sewn letters, 3" lime Scotchlite, sewn periods 14. Additional lettering: 7 sewn letters, 3" lime Scotchlite 15. Embroidered American Flag – right sleeve 16. Custom Department Identification – left sleeve 17. Hooks & Dees / Zipper Interior 18. Comfort Chinstrap – Black Knit Material 19. Liner within 1" of Hem 20. Dead Air Panels 21. Coat Cuffs – Arashield, Black 22. Half Hi Bellows Pockets – 7" x 9" x 1.5" 23. Handwarmers behind Bellows Pockets 24. EZ Grip Flaps – Black Gold 25. Mic Tab – Stormflap 26. Large Hook with Velcro Strap – right chest 27. Sub Wristlets – Long with turned thumbhole, Nomex, black Pants 1. Outer Shell: Agility with FREEFAS, Black Gold 2. Thermal Liner: Glide Ice 2 Layer 3. Moisture Barrier: Stedair 3000 4. Inspection Port Liner 5. Detachable Liner 6. Trim: NFPA lime 2-tone Scotchlite (3"), Double-Stitched 7. Wide 2" Velcro Fly with Hook and Dee 8. Half Angled Cuffs – Arashield, Black 9. Pant Cuffs – Arashield, Black 10. 3D BiFlex Heat Channel Knees – Arashield, Black 11. 3D BiFlex Knee Padding – ¼" Silicone, CCHR 150 12. Standard Bellows Pockets – 9" x 9" x 1.5" 13. Velcro pocket closure with 3 strips 14. EZ Grip Flaps – Agility with FREEFAS, Black Gold 15. Full Kevlar Lining 16. Tool Divider – Kevlar, 6" High (2 compartments) 17. Tool Divider – Kevlar, 4" High (3 compartments) 18. Suspenders: Dyna-Fit with Snap Attach and Quick Adjust
