5. APPROXIMATE BODY DIMENSIONS 5.1 108" length 5.2 96" width 5.3 40" height, and 60”at raised front vertical compartments. 5.4 54" floor width 5.5 20" compartment depth 6. COMPART MENTATION 6.1 Street Side: 6.1.1 Front Vertical: 60” height raised front vertical compartment. 6.1.1 Compartment partially filled with a C-Tech drawer system from bottom to approximate 40” height. 6.1.3 Above the drawers will be Two (2) 250 lb. capacity fixed shelves. 6.1.3 One directly above the drawers and a second shelf splitting the remaining space evenly. 6.1.2 Horizontal: C-Tech drawer system filling entire compartment. 6.1.3 Rear Vertical: C-Tech drawer system filling entire compartment. 6.2 Curb Side: 6.2.1 Front Vertical: 60” height raised front vertical compartment for gas bottle stowage/transport. 6.2.1.1 Will have gas bottle retainer bracket for two gas bottles, 2” straps with over center buckle. 6.2.1.2 Shall have 11ga. Tread plate overlay to reinforce compartment floor/bottom and door frame. 6.2.1.3 Will have two louvered vents in the front-end panel. 6.2.3 Horizontal: Two (2) 250 lb. capacity pull out shelves, mounted in upper half of compartment, with twenty (20) drawer dividers provided. 6.2.4 Rear Vertical: Two (2) 250 lb. capacity pull out shelves, mounted in upper half of compartment, with twenty (20) drawer dividers provided. 6.3 Detail of C-Tech Drawer Systems 6.3.1 Heavy duty steel drawer system. 6.3.2 Variety of drawer depths. 6.3.3 Drawer slides rated at 500lbs 6.3.4 Latching drawers with dual action handles. 6.3.5 Standard color. 6.3.6 Two (2) front to rear dividers per drawer will be provided. 6.3.7 Two (2) side to side dividers per drawer will be provided. 7. ADDITIONAL EQUIPMENT AND ACCESSORIES 7.1 1/8-inch steel tread plate overlay on compartment backs, compartment tops, bulkhead, inside tailgate panel, and cargo floor. (compartment ends need no overlay) 7.3 No Line-X or Rhino coating required. 7.4 Heavy-duty double spring retainer door holders on all swing open doors, with cable stays or chains on drop down design doors. 7.5 Weatherproof, slam type, paddle latches on all doors, with key locks and automotive type neoprene door seals. 7.6 Power compartment door locks with Two (2) key fobs per unit. 7.7 Full-length stainless-steel door hinges. 7.8 Torsion boxed understructure with minimum 1/8" steel tread plate floor. 7.9 Louvered or punched rear window protector required. 7.10 Two (2) entry grab handles at rear of body. 7.11 1/8" aluminum tread plate rock guards on lower front corners. 7.12 Rubber dual tire width rear mud flaps, non-monogrammed. 7.13 Full length drip molding. 7.14 Double panel 12" high tailgate, automotive type slam latch with link arm or coated steel cable supports. 7.15 Supplied Ford factory backup alarm relocated as needed. 7.16 Final installation of supplied Ford factory rear camera to view trailer hitch and rearward area. 7.16.1 Camera will require some sort of protection either by placement or fabrication of a guard. 7.17 One (1) Oxy/Acetylene 100-foot Hose Reel, Coxreel Model EZ-SWH-100 (no exceptions). 7.17.1 Reel shall include and be equipped with 100’ hoses, with whip hoses routed into the curbside front compartment with enough length for easy attachment to city owned bottle regulators. 7.17.2 Reel shall be mounted on top of horizontal curbside compartment, and as close to the bottle compartment as possible, with hose pulling off the curbside of the truck.
