General Specifications for Both Locations: • Remove carefully and properly dispose of existing door material, hardware, tracks, and opener. • General Raynor door specifications are attached SECTION 08 33 23 - ROLLING SERVICE DOORS ROLLING SERVICE DOORS Provide and install DuraCoil Rolling Service Doors as manufactured by Raynor Garage Doors (no substitutes): 1. Operation: Electric motor. 2. Curtain: Interlocking roll-formed slats as specified below. Endlocks shall be attached to each of alternate slat to prevent lateral movement. a. Large Curved Slats: Steel 22 gauge (0.030 inch minimum thickness). b. Material: Commercial quality hot-dipped galvanized (G-90) steel in accordance with ASTM A-653. c. Color and Finish: 1 finish coat of gray polyester paint over 1 coat of primer. 3. Endlocks: Zinc-plated malleable cast iron fastened with two zinc-plated steel rivets. 4. Bottom Bar: Two angles, minimum 1-1/2 x 1-1/2 x 1/8 inch (38 x 38 x 3 mm) with singlecontact type bottom astragal. a. Material: Roll-formed galvanized steel angles. b. Color and Finish: Roll-formed steel angles to be galvanized. 5. Guide Assemblies: Three structural angles, minimum 3 x 2 x 3/16 inch (76 x 51 x 5 mm) and fitted with removable curtain stops. a. Material and Finish: Structural steel. 1 coat of black rust-inhibitive primer. 6. Guide Weatherseal: To inhibit air infiltration between the guide and the curtain. a. Brushseal with an aluminum retainer. 7. Counterbalance: a. Barrel: Minimum 4-1/2 inches (114 mm) OD and 0.120 inch (3 mm) wall thickness structural steel pipe. Deflection of pipe under full load shall not exceed 0.03 inch (0.8 mm) per foot of span. b. Counterbalance: Mechanism with helical torsion springs, grease packed and mounted on a continuous steel torsion shaft. 1) 80,000 High cycle springs 8. Brackets: 3/16 inch (5 mm), minimum, steel plate, attached to wall angle of guide assembly with 1/2 inch (13 mm) diameter Grade 5 bolts. Inside of drive bracket fitted with sealed ball bearing. a. Finish: 1 coat of rust-inhibitive primer. 9. Enclosures: a. Hood Type: Round. b. Bracket Covers: To enclose door mechanisms. c. Material: 24 gauge steel (0.022 inch minimum thickness) commercial quality hotdipped galvanized steel in accordance with ASTM A-653. d. Color and Finish: Gray polyester paint to match curtain. e. Hood Baffle: With rubber seal to inhibit air infiltration through hood cavity. ELECTRIC OPERATORS Provide and install ControlHoist (UL Listed) as manufactured by Raynor Garage Doors: 1. Model: Raynor ControlHoist Optima: Type: Jackshaft with manual chain hoist. a. Motor Horsepower Rating: Continuous 2 HP. b. Electrical Requirements: 460 volt three phase. c. Duty Cycle: 30 cycles/hour or 300 cycles/day. d. Control Wiring: Solid state circuitry with provisions for connection of a monitored reversing device, external radio control hook-up and maximum run timer. Provisions for timers to close and mid stop and lock bar sensor capability. 1) Monitored electric reversing edge on door. Highway Division: 19600 75th Street, Bristol, WI 53104. Kenosha County to lower and fill existing opening to leave a rough opening of 30 feet for new door. Door dimensions are approximately 30’ high x 20’2” wide. Kenosha County to lower and fill existing opening to leave a rough opening of 30 feet for new door. Contractor is responsible to verify all measurements. Salt Shed: Wisconsin DOT Salt Shed 5195 120th Avenue Kenosha, WI 53144: Door Dimensions are approximately 29’5” High x 18’8” Wide. Contractor is responsible to verify all measurements.
