Overall Specifications yes___ no___ Rated Net Power (ISO 9249) shall be no less than 67 hp yes____ no__ Machine standard transport length shall be no more than 20'9" with Counterweight yes___ no___ Must must be equipped with 4 way Angle blade with float with Bolt on Cutting edge yes___ no___ Machine transport height shall be no more than 8'11" yes___ no___ Machine operating weight shall be no less than 18,500 lbs and no more than 20,000 lbs yes___ no___ Macine overall track width shall be no more than 88" yes___ no___ Machine must have a minmum reach at ground level of 22' 6" yes___ no___ Selling dealer must have a service/warranty facility within 16 miles of Desoto Cty Central maintenance shop yes___ no___ Machine must be equipped with Hyd Quick Coupler yes___ no___ Machine must be equpped with Hydraulic Thumb and 36" Digging bucket yes___ no ___ Machine must include a 48" ditching or mop bucket yes___ no ___ Service and parts manual included Engine yes___ no___ Engine shall be certified to EPA Final Tier 4/EU Stage IV yes___ no___ Engine shall have four cylinders and a displacement of no less than 202 cu in (3.3 L) yes___ no___ Engine shall have auto-idle mode to reduce engine speed when hydraulics are not in use to reduce fuel consumption and noise yes___ no___ Engine oil interval shall have a scheduled 500 hour interval for reduced operating costs yes___ no___ Engine Cooling system shuld have a capacity no less than 3.5 gal yes___ no___ Fuel Tank shall have no less than 33 gal Capacity yes___ no___ The engine will have a cold start aid such as glow plugs yes___ no___ The engine oil capacity shall be no less than 3.2 gal Cooling yes___ no___ Engine coolant shall protect the machine to temperature of -34°F (-37°C) yes___ no___ The radiator and oil cooler will be protected with a trash screen to protect against debris entering coolers yes___ no___ Cooling fan shall be variable speed, viscous clutch Power Train yes___ no___ Two speed propel will be standard with auto-shifting when travel motors encounter heavier load. A switch will be provided to allow selection of either high or low speed propel yes___ no___ In low travel speed, the machine shall reach 1.9 mph (3.1 km/h) and in high speed shall reach 3.1 mph (5.0 km/h) yes___ no___ The hydraulic pilot levers shall have short stroke and low effort to reduce fatigue. yes___ no___ The Swing torque shall be no less than 12,244 yes___ no___ The propel brake shall be spring applied and hydraulically released Hydraulics yes___ no___ The hydraulic system shall be open center, load sensing yes___ no___ The main pumps shall be three variable-displacement axial-piston pumps with maximum flow of 2 x 19 + 15 gpm. yes___ no___ Boom and arm shall have reduced drift valves for greater stability and positioning Electrical yes___ no___ The electrical system shall have 2 12 volt batteries and alternator rating no less than 60 amp yes___ no___ Machine must be equipped with factory led lighting and 270 Degree camera system shown on a 8' LCD screen yes___ no___ The fuse box shall be in the cab, well protected from the elements and shall be opened without tools. yes___ no___ A safety cover will protect the positive terminal of the battery Undercarriage yes___ no___ The undercarriage shall have one carrier roller and five track rollers per side yes___ no___ Track and carrier rollers shall be lubricated for life yes___ no___ Drawbar pull shall be at least 15,961 yes___ no___ The track shall be sealed and lubricated to extend service life yes___ no___ Ground pressure with 18 in (450 mm) rubber crawler pads shall be no more than 5.6 psi (39.0 kPa) Upperstructure yes___ no___ Right and left hand exterior mirrors shall be standard yes___ no___ Window bars shall be provided to prevent contact with a moving boom yes___ no___ The skirt bottom of the house shall be a D-channel design to improve durability
