1. ITEM NO. 1 COOLER - FREEZER STORAGE ASSEMBLY - MAIN KITCHEN - OWNER FURNISHED CONTRACTOR INSTALLED – LEARNERS SUPPORT CENTER (LSC) Manufacturer: American Panel Model: --- Size and Shape: Refer to drawings Alternate: Thermo-Kool, Kolpak 1. Manufacturer to review final installation and provide a letter confirming installation meets manufacturer requirements. 2. Field verify existing assembly dimensions and interior ceiling height and replace with same dimensions. 3. 304 #3 finish 20 gauge stainless steel finish where exposed, 26 gauge Acrylume where concealed. 4. Threshold to be smooth and level with finished floor. - Critical. 5. Provide Foot Treadle at each door 6. 4" factory floor with diamond treadplate finish with reinforced 36” internal ramp integral to floor assembly. 7. Interior walls to be .040” aluminum, white embossed texture on walls. 8. Ceiling to be embossed textured .040" aluminum baked white enamel. 9. One (1) 36" door. Door to be 18-gauge stainless steel, type 304 (18-8), #3 finish, with heated perimeter / door jambs / windows and threshold heaters. Each door to be equipped with 3'-0" high diamond tread kick plate on both sides of door. Mount hinged doors on two (2) Kason model no. 1346 (or equal); polished chrome plated nylon cam-lift hinges. Proper installation of the door system should allow for the door to self-close and seal around the perimeter of the door opening and at the floor threshold. 10. Provide heated illuminated Push Button Panic Alarm with protective cover and Phenolic Label “PANIC ALARM” for entrapment within Freezer (ADA mounting height). Panic Alarm Encasing is to be stainless steel (not plastic). Manufacturer to pre-run conduit within panel from Panic Alarm to panel above Freezer door for installation of Emergency Strobe/Horn. Division 26 will provide (1) external Emergency Strobe/Horn Beacon and interconnect the Push Button Panic Alarm to external Beacon mounted above the Freezer door. Division 27 will interconnect the Push Button Panic Alarm to the Building Automation System for Owner notification. Note: CNS requested one (1) strobe beacon only above Freezer door in Kitchen and no second beacon at Cafetorium. 11. Reinforcement as required to be provided above Freezer door (exterior) and panel next to door (handle side - interior) for mounting of Emergency Strobe Beacon, Push Button Panic Alarm and Release Knob. 12. Provide Kason 27C handle with the ¼ turn release 13. Manual backup vacuum release mechanism to punch hole in wall assembly to release vacuum within freezer assembly. Mechanism to include a pull-down handle with freeze-proof hand grip. Handle to have the ability to penetrate and/or punch hole in wall accordingly to assist with opening of door assembly in the event of entrapment (and failure of Frost free inside release button). Wall panel to include a knockout section to assist with requirements. Release mechanism assembly to be built-in/mounted to the door assembly structural frame to minimize mechanism tear-out and/or failure. Handle to be painted yellow with phenolic label “Vacuum Pressure Release”. 14. 18-gauge stainless steel, type 304 (18-8), #3 finish trim where adjacent to walls and enclosure panels that extend to 2" above finished ceiling. 15. Freezer One (1) lot LED light fixtures to operate in temperatures to -20 F. Lights to be installed perpendicular to coils. 16. 3’-0” high diamond tread plate at exposed exterior surfaces. Fasten to wall with stainless steel fasteners. 17. Provide door bumper at doors. 18. Compartments to have all electrical concealed within the walls or located above the ceiling. 19. Provide Manufacturers alarm/control system that includes hi/low limits. Route temperature sensor to be located to the side of evaporator coil. 20. Doors to be provided with CCI Industries, Inc., Clear-VU swinging door assemblies, Alternate: Kason. 1. ITEM NO. 2 REFRIGERATION SYSTEM - COOLER - OWNER FURNISHED CONTRACTOR INSTALLED – LEARNERS SUPPORT CENTER (LSC) Manufacturer: RDT Model: ZS1-2 EcoSmart Size and Shape: Refer to drawings Alternate: Or Equivalent 1. Air cooled system. 2. Scroll Compressors. 3. Cooler temperature to be +35 degrees. 4. EcoSmart system on demand defrost. 5. KE2 Evap Controllers located per Owner requirements. 6. All exterior piping to be aluminum wrapped. 7. System to accommodate Item No. 112 Cold Storage Assembly Cooler compartment. 8. Refrigeration rack accommodates 110 ambient temperatures. 9. S/S covered housing. Items 103 and 103.1 to be stacked. 10. Mount condensing unit on common exterior rack. Refer to Architectural and Engineering drawings for exact location of remote unit. Coordinate routing of refrigeration lines and conduit with appropriate trades. Heat tape and insulate all drain lines. General Contractor to seal all building penetrations at refrigeration lines.
