Specifications include, but are not limited to: 1. BASE VEHICLE 1.1. Ten (10) 2025 or Newer/Unused Ford Explorer Police Interceptors, or County approved equivalent. 1.2. Exterior Color: Oxford White, or County approved equivalent. 1.3. 3.3L V6 Direct Injection, or County approved equivalent. 1.4. All Wheel Drive (AWD) 1.5. Conforms to Federal and California emissions. 1.6. Include a spare tire. 1.7. Four (4) keys cut and programmed; keyed alike-1284x (59B) 1.8. Police Upgrade Package (65U) 1.9. Badge Delete 2. OUTFITTING 2.1. Window tint 2.1.1. Front windows @20% 2.1.2. Rear windows @5% over OEM tint 2.1.3. Brow @ 20% 2.2. Code 3 2.2.1. Overhead Lightbar 2.2.1.1. nRoads Fleet Series Light Bar, or County approved equivalent, with directional option. Amber/White. 2.2.2. PA System 2.2.2.1. bluePRINT 500 Series Console 100W Button Control System, or County approved equivalent 2.2.2.2. 100 watt composite siren speaker and bracket for behind grille mounting. 2.2.3. Base electrical system 2.2.3.1. Mini Patrol Power 2.2.4. Equipment Console 2.2.4.1. Install one Gamber Johnson 7170-0734-00 or County approved equivalent console 2.2.4.2. Install one Gamber Johnson 7160-0321 Motorola APX faceplate, or County approved equivalent 2.2.4.3. Install one Gamber Johnson 20033 Sound off 500 faceplate, or County approved equivalent 2.2.4.4. Install one Gamber Johnson 3130-0152 filler pannel, or County approved equivalent 2.2.4.5. Install one Gamber Johnson 19740 rock switch/AUX power filler pannel, or County approved equivalent 2.2.4.6. Install one Dual USB 2.4A charger for Contura SW Cut-out, or County approved equivalent 2.2.4.7. Install two Magnetic microphone mounts MMBP 2.2.4.8. Install one Maxxima M84434RW-A 6” red/white LED dome lite , or County approved equivalent 2.3. Radio Communications 2.3.1. Radio Communication 2.3.1.1. The Contractor shall provide all required pre-cabling of radio antennas, control cables and power cables to support the final installation of the radio equipment by the County. The specifications listed below are minimum requirements and are subject to approval by Sheriff Wireless and Data Services, before the construction and delivery of the first vehicle. All cable lengths at the front center equipment console and the rear electronics tray must be sufficient to allow proper placement of components by the County. 2.3.2. 800MHz Radio Antenna: (1) Larsen NMOKHFUDMPL or San Diego County approved equivalent, antenna NMO mount/cable shall be installed on the roof centered left-to-right and 23" from the rear roof’s edge. The antenna coaxial cabled is to be routed to the equipment mounting tray in the rear of the vehicle and labeled “Radio Antenna”. (1) Larsen NMO3E800B or San Diego County approved equivalent, 806-866MHz antenna mast shall be installed on the NMO. 2.3.3. Radio Control Head Cable: (1) Motorola HKN6169B or San Diego County approved equivalent, radio control head cable shall be routed from the front center equipment console to the rear equipment mounting tray. 2.3.4. Radio Control Head Pre-Wire: Pre-wire for the radio control head (Motorola XTL or APX -05 remote head) located in the center console must include the following circuits. A label must be affixed to the radio control head wire bundle to clearly identify the circuits. 2.3.5. 16awg Red/Black wire printed “Radio Head” to provide constant 12V from the rear fuse panel circuit #2 2.3.6. 16awg yellow wire printed “Radio 2” to provide ignition from an ignition sense wire. Could be the same used for the gun lock ignition wire. 2.3.7. 16awg black wire printed “ground” to provide ground sourced from a factory ground location. 2.3.8. 18/2 speaker wire for connection to the radio’s audio output to allow the siren to perform the radio re-broadcast (RRB) feature
