Specifications include, but are not limited to: ANCHOR BOLTS FOR STEEL POLES Anchor Bolts are used for standardized structural steel components including: mast arm signal poles; mast arms; highway luminaire poles; traffic/pedestrian signal poles, high mast light poles, and CCTV camera poles. Common anchor bolt diameters are 1 inch, 1.5 inches, and 2 inches. Design to all requirements of AASHTO Standard Specifications for Structural Supports for Highway Signs, Luminaires and Traffic Signals (current edition with all applicable interim revisions). Produce anchor bolts, nuts and washers conforming to the following specifications: Component Part Specification Anchor Bolt ASTM F1554 GR 55 Anchor Bolt Nut ASTM A563 GR A Washers ASTM F436 Galvanizing Finish ASTM A153 or AASHTO M232 Use 100% domestic steel materials melted and manufactured in the United States of America. STANDARD TRAFFIC SIGNAL, LUMINAIRE, CCTV CAMERA POLES Specifications for standardized traffic signal structural steel components including: mast arm signal poles; mast arms; signal pole luminaire extensions; luminaire arms; highway luminaire poles; high mast luminaire poles; traffic/pedestrian signal poles; CCTV camera poles, signal pole foundation adapter base; and related hardware kits. Poles should follow the requirements set forth in AASHTO “LRFD Specifications for Structural Supports for Highway Signs, Luminaires, and Traffic Signals,” (Current Edition with all applicable interim revisions). Design for basic wind speed of 115 mph. Use truck speed of 65 mph for truck induced gust in fatigue calculations. Design all structures to Category I fatigue importance factor. Steel signal pole, mast arm, luminaire extension pole, and luminaire arm designs must be reviewed and approved by a Utah licensed structural engineer. Final calculations must be stamped and signed. Use the following material specifications: Component Part Specification Pole Shaft (tapered) ASTM A595 GR A or ASTM A1011 GR 55 Mast Arm Shaft (tapered) ASTM A595 GR A or A1011 GR 55 11 GA Cone ASTM A1011 GR 55 Plate ASTM A36 Pipe ASTM A501 GR B or A500 GR B or C Bar Handhole Frame ASTM A529 GR 50 (preferred) or A572 GR 50 or A500 GR B or C Pole Top Cap ASTM A1011 Mast Arm End Cap ASTM A1011 Stainless Steel Hardware AISI 300 Series Flange/Arm Connection Bolt ASTM F3125 Flange/Arm Connection Nut ASTM A563 GR DH Flat Washers ASTM F436 Arm Joint Stud ASTM A36 Lock Nuts ASTM A563 GR DH Structure Finish AASHTO M111 (ASTM A123) Hardware Finish ASTM A153 Use 100% domestic steel materials melted and manufactured in the United States of America. Meet minimum current AWS D1.1 weld testing requirements. Meet AISC Highway Component Manufacturers (CPT) certification. Provide plastic handhole covers for mast arm signal pole, traffic/pedestrian pole, CCTV camera pole, and luminaire pole with spring-loaded attachment clamp and tamper resistant screws. Vendors must have a minimum of 5 years of experience designing, manufacturing, and producing galvanized steel traffic signal and lighting pole products for major public sector users including State Departments of Transportation, large cities, or counties. HIGH MAST LUMINAIRE POLES High mast luminaire poles and related hardware kits. Poles should follow the requirements set forth in AASHTO “LRFD Specifications for Structural Supports for Highway Signs, Luminaires, and Traffic Signals,” (Current Edition with all applicable interim revisions). Design for basic wind speed of 115 mph. Use truck speed of 65 mph for truck induced gust in fatigue calculations. Design all structures to Category I fatigue importance factor. High mast luminaire pole, anchor bolt (if applicable), and foundation designs must be reviewed and approved by a Utah licensed structural engineer. Final calculations must be stamped and signed. Use ASTM A572 GR65. Use 100% domestic steel materials melted and manufactured in the United States of America. Meet minimum current AWS D1.1 weld testing requirements. Meet AISC Highway Component Manufacturers (CPT) certification. Provide plastic handhole covers for high mast luminaire poles with spring-loaded attachment clamp and tamper resistant screws. Vendors must have a minimum of 5 years of experience designing, manufacturing, and producing galvanized steel traffic signal and lighting pole products for major public sector users including State Departments of Transportation, large cities, or counties.