Specifications include, but are not limited to: 1.1 Die-cut parcel post mailer, 200#, 'E' flute, White with tuck-top. Kit shall be pre-sealed with two Security Seals. The kit box dimensions shall be acceptable as long as all components fit easily into the box. Printing shall be in two colors, black and red. Sides of box are to be printed in black ink. (Example sizes are 7.5" L x 6.5" W x 2.5" H or 8"L x 4.5"W x 2.5"H. ) (EXHIBIT A) 1.1a. Biohazard seal symbol and BIOHAZARD printed in Black ink with a fluorescent orange or red background on exterior of top lid box. (or an equivalent biohazard label maybe affixed to the box.) 1.1b. “ATTENTION: CRIME LAB If Subject is Deceased: Check here ” is to be printed in red ink in BOLD on exterior of top lid under address. 1.1c "NOT TO BE USED FOR DNA EVIDENCE" printed in red ink in BOLD CAPS on exterior of top lid under printing outlined in (b) above. 1.1d "ATTENTION: DO NOT PLACE SUBMISSION FORM(S) INSIDE SEALED PLASTIC EVIDENCE BAG" is to be printed on interior of top lid of box in BOLD Caps. (or an equivalent label maybe affixed to the inside of the box.) (EXHIBIT B) 1.1e Kit expiration date shall be printed on left side of box exterior. (This will be date blood tubes expire.) (EXHIBIT C) 1.2 One (1) Molded Holder Insert: (to protect specimens during transport) Foam holder, which will slide into sealed plastic bag and fit back into outside box. Holder must be molded to fit individual contents for protection during shipping. 1.3 One (1) Envelope: Envelope is to be slightly smaller than the bottom of kit box with side opening. Envelope is to be affixed to the bottom kit box with an adhesive which will hold envelope with enclosed Instruction Card and Request Form card securely. The envelope should be able to be resealed. (EXHIBIT D) 2 SPECIFICATIONS FOR COLLECTION CONTENTS: 2.1 Two (2) Blood tubes, 10 mL grey stopper, containing 100 mg of sodium fluoride and 20 mg. of potassium oxalate. 2.2 One (1) 21 gauge x 1.5" multi-sample needle and holder collection system, equivalent to vacutainer brand 2.3 One (1) Povidone Iodine (PVP) Prep pad. (*alcohol free*) 2.4 One (1) polypropylene urine container with cap able to contain a minimum of 60 mL liquid volume (e.g. 60-100 ml). Round container with 48 mm opening. Container is clear (untinted) with 10 mL graduations. Cap has special O-ring design and is leak resistant. 2.4a One (1) Digital design temperature monitor strip. The temperature range is 90 to 100 degrees Fahrenheit and registers as a green indicator. Strip is to be adhered by the manufacturer to lower section of urine polypropylene container described section 2.4 2.5 One (1) Clear Tamper Evident Bag (minimum of 3 mil polyethylene) shall measure approximately 9" x 11", or large enough to contain evidence contents easily, with two color printing on front. All printing shall be black except biohazard symbol, which is black and orange, Bag shall have pouch on front for insertion of documentation and enough width to accommodate Request Form. Except for print, bag & document pouch shall be clear (untinted). (EXHIBIT E) 2.6 One (1) Absorbent Sheet. Will absorb up to 90 ml of liquid inside plastic Tamper Evident bag 2.7 One (1) latex-free tourniquet 1” x 18” 3 SPECIFICATIONS FOR TAMPER EVIDENT SEALS: (EXHIBIT F) 3.1 One (1) Urine Bottle Security Seal, large enough to securely seal bottle, (e.g. 1" x 7.75 total = 7" label w .75" tab) flood coat - clear Print color RED 3.2 Two (2) Blood Tube Security Seals large enough to secure blood tube, (e.g. 5 x 4.5" total = 4" label w.5" tab) flood coat - clear with serrated. Print color RED 3.3 Two (2) Box Security Seals, red, print color black.