Specifications include, but are not limited to: 6.1.1 Trailer shall be no more than thirty (37) feet long _______ _______ 6.1.2 Trailer payload capacity a minimum of twenty (20) ton _______ _______ 6.1.3 Trailer shall have two (2) axles twenty thousand (20,000) pound capacity _______ _______ 6.1.4 Trailer shall have oil seal hubs on the axles _______ _______ 6.1.5 Trailer to have two (2) axle spring suspension, with fifty thousand (50,000) pound spring rating capacity _______ _______ 6.1.6 Trailer shall have S-Cam type air brakes on all axles and an ABS system _______ _______ 6.1.7 Both trailer axles shall have spring air brakes, automatic slack adjusters and outboard brake drums _______ _______ 6.1.8 Trailer Tires/wheels to consist of eight (8) 235/75R x 17.5 18 ply tires and steel disc hub piloted wheels or manufacturers recommendation _______ _______ 6.1.9 Trailer deck shall be twenty-four (24) feet long, stationary deck shall be four feet long (4) tongue shall be Min Six (6) feet long, making total length thirty (34) feet long _______ _______ 6.1.10 Trailer shall have a stationary deck, which will have a full four (4) Foot Long by 102” Inches Width _______ _______ 6.1.11 Tilt deck to be one hundred and two (102) inches wide and twenty-four (24) feet long _______ _______ 6.1.12 Trailer decking shall be decked with oak and a minimum thickness of one and a half (1 ½) inch thickness _______ _______ 6.1.13 Trailer shall have Sixteen (16) total d-rings, Eight (8) per side _______ _______ 6.1.14 Trailer shall have a three (3) inch I.D. pintle hitch with four (4) bolt mounting with a GTW of ninety thousand (90,000) pound rating _______ _______ 6.1.15 Trailer shall have a gear drive, two speed, crank style jack with a minimum rating of twelve (12) thousand pounds _______ _______ 6.1.16 Trailer shall have two (2) safety chains, a minimum of a half (1/2) inch chain with hooks _______ _______ 6.1.17 Trailer shall have heavy duty cylinder to control deck action and dual cushion cylinders with air assist _______ _______ 6.1.18 Trailer I-beam frame construction shall be of hi-tensile steel _______ _______ 6.1.19 Trailer shall have no less than ten (10) inch main frame I-beams and eight (8) inch side frame beams _______ _______ 6.1.20 Trailer shall have no less than ten (10) inch main frame on tilt bed with I-beam cross members no more than sixteen (16) inch centers, and all steel components made of hi-tensile steel _______ _______ 6.1.21 Trailer shall have a way to lock the deck down when equipment is on the trailer _______ _______ 6.1.22 Trailer shall have a sealed LED light package with reflective tape _______ _______ 6.1.23 Trailer wiring shall run through conduit with rubber grommet protection at each cross member _______ _______ 6.1.24 Trailer electrical system shall be twelve (12) volts with a seven (7) way round male connector _______ _______ 6.1.25 Trailer shall be sandblasted and cleaned of any weld slag or dirt before priming with a rust inhibitor primer _______ _______ 6.1.26 Trailer shall be top coated with Powder coat _______ _______ 6.1.27 Trailer to be equipped with a DOT approved Under-Ride Protection device with a beaver tail approach for easier loading, see attached drawing _______ _______
