Specifications include, but are not limited to: ONE (1) ONLY TRUCK CAB AND CHASSIS: Specifications (minimum) unless otherwise noted as follows: To be 2022 year model – 26,000 lb. GVWR (maximum) – Axels: 8000# front, 17,500# rear – wheelbase to provide cab to axle measurement of approximately 140” to properly mount the 16ft van type body described in Item 2a and the electric hydraulic cargo lift described in Item 2b – 320hp gas engine with equivalent torque – air intake warmer or equal heating device for induction system – air conditioning - 6 speed Allison 2500 series w/push button automatic transmission or equivalent – emergency park brake - single speed rear axle – auxiliary rear springs – block engine heater - intermittent 2 speed windshield wipers with washers –tire size to meet axle GVWR and coincide with finished floor platform height of 43” to 44”, 255/80R22.5, 14 ply type tires on hub-piloted wheels (front and rear), highway type front with mud flaps and mud and snow rear – finished floor platform height shall be between 43”” and 44”.-.fresh air heater and defroster – power steering– AM/FM radio – min. gear ratio of 5.29 - 150 AMP alternator –LH 50 gallon aluminum fuel tank – (2) 900 CCA batteries – dome light in cab – sun visors on right and left sides – arm rests on right and left sides of doors – grab handles on cab right and left side – tinted glass windshield – painted front bumper - dual stainless steel 7”x16” outside mounted electric closing mirrors and 8” convex mirrors on right and left side to properly clear a van type body 96” wide – total width must not exceed 112” from mirror to mirror when in open position - gauges for voltmeter, oil pressure, engine temperature and transmission temperature – heavy duty front shock absorbers – standard cab and vinyl upholstered drivers seat w/2 person passenger seat – hydraulic bra kes – five amber marker lights mounted on cab – all lights required by DOT – overall truck length cannot exceed 28’8” - 2018 EPA guidelines must be meet- permanent type antifreeze to –30F – paint color: white - with operators manual. ONE (1) ONLY VAN TYPE BODY TO BE MORGAN, DELTA WASECA OR SUPREME BODY CORPORATION UNIT OR EQUAL: Specifications (minimum) unless otherwise noted as follows: For dry cargo – 84” high door opening – inside length 15ft 6” inside height 90”, inside width 92”, outside width 96” – ½” fiberglass reinforced plywood walls and front – aluminum extrusion front corners – top body corners (only) to be cast aluminum – white color inside and out – 12” steel scuff plate 1/8” thick on inside front and walls – 3” steel “I” beam cross-members on 12” center under floor – 10 or 12 gauge steel rear frame painted white - .032” aluminum roof – 1” 18 gauge galvanized formed hat section roof bows to be spaced not more than 24” on center – 12” radius front to roof – ¾” metal reinforced, aluminum covered or composite full width roll up door – nylon rollers on door – undercoated 1 1/8” laminated hardwood floor with varnish on interior flooring – two rows of series “E” cargo track installed on sides to secure ovens and carts to sidewalls, lower row to be 22” O.C. high and upper row 48” O.C. – all lights required by DOT – two interior dome lights with switch at rear – audible electronic back up alarm, 97 decibel minimum wired to back up lights – anti-sail mud guards 24” x 36” mounted behind rear wheel on body – to be properly mounted on cab and chassis as described in Item 1, floor platform mounted approximately 44” from ground, consideration given to mounting electric/hydraulic cargo lift described in Item 3. Mud flaps installed on rear of chassis, 6” off ground. ONE (1) ONLY ELECTRIC/HYDRAULIC CARGO LIFT: Specifications (minimum) unless otherwise noted as follows: Lift gate: Wide-arm low maintenance general purpose. Capacity: 3000 lbs. Platform: 50” x 80” wedge (continuous taper) with self leveling platform shall have a dual direct torsion spring to assist the operator in opening and closing the platform. Rubber bumper platform. Flip over support: full length formed steel shelf to support the flip over. Handles in both sides to pull platform out. Dock extension plate: High strength 3/8” thick diamond plate, supported by heavy duty tubing and channel, undercoated to prevent rusting. Self-lubricated bearings: Ten (10) self-lubricated bearings on load bearing pins. Replaceable Pins: Bed Height: Minimum 45” to maximum 48” w/body laden, 54” max. w/body unladen. Control: Four(4) sealed toggle style control switches mounted two(2) at 64” and 2 at 88” from ground floor. Wiring to lift to have disconnect switch to the battery.
