Specifications include, but are not limited to: 1.ENGINE1.16.7L - V8, Turbo Diesel, minimum 300 HP @ 2800RPM, 660 Ft. lbs. Torque rating @ 1600 RPM.1.2H.D. auxiliary engine oil cooler.1.3Hour meter.1.4H.D. Coolant protection permanent anti-freeze to -35 F.1.5Water/fuel separator.1.61000 watt, 110 volt block heater withrecessed plug located under LH door.1.7Diesel Fuel tank/40 gallon. Fuel tank mustnot interfere with the installation of the dumpbody.1.8Urea (DEF)/6 gallon.2.TRANSMISSION2.1Six-speed automatic with overdrive.2.2H.D. Auxiliary transmission oil cooler.2.3Power takeoff six (6) bolt, left hand side.3.SUSPENSION3.1GVWR 19,500 lbs., minimum.3.2H.D. front & rear stabilizers. 3.3 Front axles and springs, 7,000 lbs3.4Rear axles and springs, 13,660 lbs.3.5H.D. front & rear shocks.3.6Cab-to-axle dimension to be suitable fordump body.4.STEERING4.1Full power.5.BRAKES5.1Brakes must be the heaviest dutyavailable for the vehicle specified.5.2Front and rear disc, power assisted withfour wheel antilock.ELECTRICAL/CAB6.6.1Heavy duty 12 volt starting system.6.2Battery H.D. 1500 C.C.A.6.3Alternator - 200 amp. minimum, singleunit only .7.TIRES AND WHEELS7.1225/70R x 19.5 G, two (2) all-season onfront, four (4) traction on rear.7.2Full size mounted spare, same as front.7.3Provide valve extenders so all tires canbe inflated from outboard of vehicle.7.4Wheels 10-hole disc, 19.5" x 6"k, RWsteel.7.5Hydraulic jack & lug wrench.8.CAB8.1Conventional - 3 man - all steel or withtilting fiberglass hood and fenders witha stationary grille. 8.2Heavy duty dark vinyl covered fulllength bench seat (40-20-40) or bucketseats with seat belts.NOTE: Center section of bench seatmust be removable for mounting ofhydraulic controls.8.3Dual sun visors and arm rests.8.4Tinted glass all around.8.5Heater/defroster.8.6Floor covering black vinyl.8.7Intermittent windshield wiper systemwith washer.8.8Telescopic heated mirrors with built-inconvexs.8.9Factory installed cab running boards.8.10Front frame mounted tow hooks.8.11Gauges including volt meter, fuel level,oil pressure, water temperature,tachometer.8.12Power outlet, two (2).8.13AM/FM radio with clock.8.14Factory installed air conditioning.8.15Five clearance lights.8.16Provide two (2) side window clearplastic weather guards.8.17Upfitter switches, minimum four (4).9.SAFETY9.1Must meet all Federal and Staterequirements.9.2Back-up alarm. Provide a 12-Voltaudible warning device which shall beactivated when the vehicle is shiftedinto reverse.Preco Inc #45AA or approved equal. 9.3 Provide one (1) five (5) lb. ABC FireExtinguisher with vehicle bracket.Amerex Model #500T. (No Substitute)9.4Provide a three (3) triangle flare kit withstorage box.10.STAINLESS STEEL DUMP BODY10.1This specification shall describe a 304stainless steel cross memberless typedump body or approved equal. Biddermust submit with their bid, completespecification and descriptive literatures.J&J Model DSS1/BC or approvedequal. All body dimensions aremeasured from the top of the floor.10.2Approximately 8.1" long inside lengthby 7' wide inside width. Bed mustaccommodate a 4' x 8' sheet ofplywood with tailgate closed. (12 ga.)304 stainless steel. Note: Frontmirrors must extend beyond sides ofbody.10.320" side height, (4 yard water level).10.426" front height/rear tailgate.10.5Grip strut ladder/step, both sides ofbody, mount front corners.10.6Full length tarp rail each side of body.10.7Gussets, fore and aft, with a 2" x 6"oak side board extension.10.8All welding continuous throughout bodyand shield, and to be chipped andground free of slag.10.9Body to have no open areas whereroad splashes or salt can be trapped.10.10 All sharp corners must be rounded.10.11 Provide a telescopic roller assembly, towhich a fixed crank winds the coveronto the roller assembly. Rear bowsections allows the cover to be easilysecured with tie down straps. Provide afull load asphalt tarp cover with a wind. Deflector. Must be operable from theground by one person, maximum 74"from ground to center of crank handle.Pioneer model #EDD-1500DA(Aluminum).10.12 Full width rear skirt with the I.C.C. lightsmounted at the lowest section of theskirt.10.13 Required OSHA safety equipmentinstalled including safety body prop.10.14 Provide a tool box behind the cab,fastened to the frame, maximum 24"wide, full width, constructed of 10 ga.304 stainless steel material, height tobottom of window with a plywood lineron floor. Two (2) full sided lockablereinforced doors with T-handles. Doormust open toward cab and open withthe dump body in the down position.Box must be weather-proof, selfstanding and protected from damage byframe flex. Note: If tool box is to bewidened to offset the hoist, exhaust orfuel tank this must be included in thebid price. No Exception.10.15 Body to be equipped with ring andchain for dump body lever.10.16 Front steel splash guards, rear anti-sailmud flaps.11.CAB SHIELD11.1Cab shield to extend 48" (3/4) forwardof the front of the dump body and allowa maximum of 4-1/2" above the cab forclearance.11.2Cab shield to be of 12 ga. 304 stainlesssteel, load bearing and contoured to fitin with the balance of the frontal area.12.FLOOR12.17 ga., 304 stainless steel, with 2" radiusformed into floor. All welds to run thelength of the body. 2.2One piece, no seams, 5", 10lbs. perfoot I-beam long sills.12.3Maximum mounting height, truck frameto body floor, 12
