1. Custom Bed Cap Installation: Install a SCEMS-Provided Iconic X-One custom bed cap to the truck bed according to the manufacturer’s instructions. Bed cap upfit should be installed in such a way that all electrical cabling has a single-entry point into the chassis. 2. HVAC System: Provide and install variable speed DC R134a refrigeration compressor that requires no interface into vehicles existing OEM HVAC system. The unit shall be as compact as possible, weighing no more than 40 pounds and maximum height of 9” and a footprint maximum of 30” by 30”. HVAC unit shall be installed on the roof of the Cap and not interfere with emergency lighting and communication antennas. The electric HVAC system shall be powered independently using a Xantrex brand 110 volts to 12-volt invertor and a minimum of 125 Ah lithium-ion battery for a minimum standalone run time of HVAC system without 110v shoreline power for 120 minutes. Interface to the OEM electrical system for recharge of the lithium-ion battery with a battery-tobattery converter shall be supplied and installed. Install and interface/mount a 110-volt heater and connect to the Xantrex converter. The system shall have an HVAC controller installed with the capability of separating heat and air conditioning at temperature set points established by SCEMS. The system shall have all the appropriate shielding including any exposed lines or wires shall have provisions (shields) for protection and be water tested post installation. Reinforce the roof as needed to support weight and weatherproof. The HVAC units shall only heat/cool the main sliding tray portion of the truck cap 3. Opticom: Integrate with OEM to turn off when vehicle is in park, if this is not possible, a manual switch shall be provided and placed on the center console that cuts off the Opticom when the vehicle is placed in the "park" position automatically. The light bar (a Whelen Liberty II.) shall be reprogrammed to reactivate the Opticom when vehicle is taken out of the park position. Door Locks: The driver’s door shall be rekeyed by First State Collision Center in Georgetown to the SCEMS standard key by the upfitting vendor. Locks for the Iconic X-One Cap shall be tied into lock/unlock with chassis electric locking system. 4. Idle Shut Off Programming Delete: The programming on the Silverados that shuts off the engine after idling for 30 minutes must be deleted at First State Chevy Service Department in Georgetown by the upfitting Vendor. Supporting documentation for this work will be provided by the county for GM to allow this. 5. Back Up Camera Install a backup camera over the third brake light on the cap that displays on the original dash screen on the chassis when the vehicle is in Reverse. 6. DriveCam Provide and install a wiring harness for a Lytx Drivecam into the OBD port. The camera-side plug shall exit the ceiling of the chassis on the right side of the rear-view mirror. 7. Internal Grab Handles Provide and install looped webbing handles on each door of the cap to make it easier to grab and pull the doors closed. These shall not interfere or catch on any door latches. 8. Battery Jumpstart Hub: Provide and install a polarity protected battery boosting/jumping connector hub with a protective, weatherproof cover to the front grill. Jumper cables, 25 ft length, with heavy duty clamps on one end and the corresponding connector hub on the other end shall be provided at the delivery of the truck. 9. Light Bar 54” Whelen Liberty II WCX Must use SCEMS provided drawing. a. Whelen model BH321111 b. Install on roof with all modules used including front take down and side alley light. The light bar shall be alternating red/blue with tri color on rear to include amber. a. Connect LED Opticom with a “park kill” switch, can use OEM switch to depower when placed in park but must repower when vehicle placed in drive. Program to work only when WeCanX is on slide position 1, 2 or 3. b. Alley lights on separate WeCanX switch, controlled left and right and all on when Scene button is pressed. c. Take down lights- programmed to flash when on WeCanX on position 3, then light solid when Scene or Take Down button selected.
