9-FT UTILITY (SERVICE) BODY: 191 _____Furnish and install a steel utility body to fit the selected chassis 192 _____Utility body dimensions to be approximately 79” wide x 108” long x 38” high with 49” floor 193 width 194 _____Horizontal top opening compartments with aluminum diamond plate lid cover and interior 195 dividers on 4” centers 196 _____Three (3) compartments per side: 15” deep compartments. 38” height overall 197 o #1 34” x full height vertical 198 o #2 46” x 18” horizontal compartment 199 o #3 28” x full height vertical 200 _____Utility body shall be attached to the frame at six (6) mounting points with grade eight bolts 201 and nylon lock nuts Understructure to include three (3) formed 10-gauge mounting crossmembers, two (2) 203 formed 10-gauge “C” channel through members and two (2) 10-gauge formed stiffeners 204 ____The flooring to be 12-gauge steel diamond plate 205 ____The bulkhead to be 14-gauge Galvanneal steel 206 ____The doorposts, the end caps and the back wrapper to be 14-gauge Galvanneal steel 207 ____The tops to be 16-gauge Galvanneal steel 208 ____All doors to have 18-gauge Galvanneal steel outer panels with 20-gauge Galvanneal inner 209 panels 210 ____Equipped with master compartment positive door locking system. System to be manually211 operated and utilize a standard padlock security. 212 ____No wire cable allowed for activating master-compartment locking mechanism. 213 ____Compartment doors shall be individually equipped with a positive three-point latching system 214 to include chrome T-bar handle with polished stainless-steel pockets and galvanized steel 215 locking bars. 216 ____All compartment doors to be equipped with barrel locks. 217 ____All barrel locks to be keyed alike with six (6) sets of keys provided. 218 ____All vertical compartments to have two (2) removeable/vertically adjustable shelves. All 219 horizontal compartments to have one (1) removeable/vertically adjustable shelf. All 220 shelves to be vertically adjustable on 2” centers. 221 ____All shelving to be 2” tall tray-style steel formed construction with built-in removable dividers 222 on 2” centers. Provide dividers in every other divider slot. 223 ____All shelves and cabinet bottoms to be lined with removable full-length non-skid Dri-deck 224 material or City approved equal. 225 ____Drop-down doors to have bolted (not riveted) detachable heavy-duty chain stays or coated 226 aircraft cable stays and include rubber bumper pads mounted on the body to prevent 227 damage to the body or the hinges when the chains/cables are removed. 228 ____All vertical compartment doors to be equipped with gas shock door retainer. 229 ____Door flanges to be completely sealed with automotive rubber door seal. 230 ____Full length, 5/16" stainless steel door shafts and hinge blocks with nylon inserts on all 231 compartment doors. 232 ____All hinge blocks to be stainless steel and fastened with stainless steel mono bolts. 233 ____Tailgate to be heavy-duty self-leveling with 12-gauge diamond plate inner panel and 1/8" 234 aluminum diamond plate end cap. 235 ____Tailgate hinges to be minimum 5/8" stainless steel Allen head shoulder bolt with 5/8" bronze 236 bushing. 237 ____Tailgate bracket to be a minimum 10-gauge stainless steel. 238 ____Furnish and install a full-length water drip cover on both sides of the utility body upper 239 cabinets to prevent water intrusion in the cabinets. 240 ____Front aluminum diamond plate gravel guards. 241 ____Furnish and install two (2) chock block holders recessed in wheel skirt panel. One (1) on 242 each side where fuel spout allows.
